Seriud AC1200 Quick Start Guide: How to set up with a smartphone / laptop / tablet

1638
Issuing time:2018-07-19 11:57

 Installation Precautions  

Seriud AC1200 Dual Band WiFi Range Extender adopts Qualcomm QCA9531+QCA9886 chip sullution,which ensures a stable signal expansion and excellent quality. It supports both2 GHz and 5 GHz bands and the default initial SSID is Seriud1200-2G andSeriud1200-5G.


After you've done the setup, its default new name (SSID) is yourexisting WiFi network name with "-2G" and "-5G" at the end.

The passworddefaults to the password of your main router WiFi to facilitate people memory and use the DE. After all Settings is complete, you can modify the password ofthe extender in20181022145251.pngAdvanced - 20181022145317.png Wireless Settings.


For Example:

Existing WiFi Network name (SSID): myhome

Existing WiFi Network password: 123456

New Extender WiFi Network name (SSID): myhome 2G and myhome 5G

New Extender WiFi Network password: 12345678


1. Make sure your ROUTER PASSWORD is correct, otherwise there will be no network after the installation is completed and you need to press the RESET button wihich is also the power lamp button for 10 seconds to restore the factory Settings, and thenset it up step by step.

2. Keep your phone constantly connected to the repeater throughout the setup process, because your phone may disconnect from the extender and connect to your router automatically, so if you can't access the login screen or youcan't go to the next step, check if your phone is disconnected from theextender.


Connect to an Existing WiFi Network

To extend therange of your WiFi network, you must connect the extender to your existing WiFinetwork. You can set it up with a wireless device such as smart phone, laptop or a PC without wireless feature ( See How to set up with a PC without wireless feature.


How to set up with a smartphone / laptop / tablet

Plug the extender into an electrical outlet proximity to the router or access point,wait for the lower lamp to light on.

In your wireless network list of your laptop or smart phone, select and connect to the extender WiFi network Seriud 1200-5G or Seriud1200-2G. Get either 5G or 2G setup and the other one will be set up at the same time. After the Settings iscomplete, you can connect to either 5G or 2G to access the internet.

Note: If y ourlaptop has only 2G network card, it will display only Seriud1200-2G, but not both two of them.

When theextender is connected for the first time, the login  interface will pops up automatically. If not, run a browser and  enter 192.168.10.1 in the address bar.  The Administrative account and password default to Admin, which you do not need to enter, justclick LOGIN .

It will scan the wireless WiFi network signals around.

Select and connect to the WiFi network you want to extend.

In the SSID field, set the new SSID for the 2G and 5G  frequency bands of your extender respectively, or use the default SSID of your home WiFi name with “-2G” and“-5G” at the end. In the Password field, type the password of the existing WiFi network and click the Apply button.

After connecting to the router, it will rebootautomatically.

Wait about 2-3 minutes, it will prompt that the installation is comlete, and the light will turn green.

Unplug theextender and move it to a new location that is about halfway between your router and the area with a poor router WiFi signal. The location that you choose must be within the range of your existing WiFi router network.

Use the Power Lamp on the front panel to help you choose a spot where the extender-to-router connection is optimal, the light is green with good signal and red with weaksignal. Locate it several times to find the optimal location.

Reconnectyour WiFi device to the new extended network.

Note: The extender defaulted network segment is 192.168.10.1, if the main router networkis also 192.168.10.1, you must modify the network segment of the extender orthe superior network first, or use the extender in Bridge Mode in20181022145251.png Advanced, see How to set up the Bridge Mode.


step1-6.png

step7-9.png


Connect an Ethernet-EnabledDevic

After the extender is connected to your existing WiFi network, you can connect a wired device to the extender using an ethernet cable. That device can then access your existing network through the WiFi connection.

20181022150225.png



Any question pls contact seriudstore@gmail.com.




Related Articles:

S‍eriud AC1200: Set up with a smartphone / laptop / tablet

Seriud AC1200: Set up with a PC without wireless feature

Seriud AC1200‍: ‍How to Find The Optimal Location

S‍eriud AC1200: More Aapplication Scenarios: How to Set up AP / Router / Bridge Mode


Share to:
Customer service
0086-400-880-7850
Postal Code:518000 Email:seriudstore@gmail.com
Rm. 6608, 66/F, Seg Square, Huaqiang North Street,

Futian District, Shenzhen,
China
Service online
 
 
 Work Time
Mon to Sat :9:30-18:30
 Contact Details
Hotline:0086-400-880-7850
Email:seriudstore@gmail.com